مقالات علمی چاپ شده در مجلات
-
"Enhanced desalination performance of an electrodialysis stack in over-limiting current by adding AC/Fe3O4 nanocomposite as a flow electrode"
Zohreh Akbari Jonoush,
Mohammad Ali Mostafaei
Journal of Water Process Engineering,
Vol. 61,
pp.105304-105317,
2024
-
"Optimizing weld strength and microstructure in CP-titanium and 304 stainless steel friction welds with chromium interlayer"
Mohammad mostafa Sheykhi,
Mohammad Ali Mostafaei
Results in Materials,
Vol. 24,
pp.100627-100640,
2024
-
"A novel approach to investigate the effect of friction stir welding parameters on hardness and grain size of pure titanium using artificial Neural Network"
Navid Siamakmanesh,
Mohammad Ali Mostafaei
Materials Today Communications,
Vol. 38,
pp.108404-108409,
2024
-
"Pre and post rolling homogenization of direct chill cast Al-6Mg alloy: Effect on microstructure and mechanical properties"
Mohammad Ali Mostafaei,
Mohsen Kazeminezhad
Advances in Materials and Processing Technologies,
Vol. 1,
pp.1-1,
2023
-
"Application of a Novel Process Called Vacuum-Encapsulated Slurry Method to Form a Silicide-Aluminide Protective Coating on Ti6Al4V Alloy"
Saeed Nouri,
Mohammad Ali Mostafaei,
Masoud Asayesh
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,
Vol. 31,
pp.9504-9509,
2022
-
"Bimodal grain size and mechanical properties enhancement in low carbon steel by ultra-rapid annealing"
Mohammad Ali Mostafaei,
Mohsen Kazeminezhad
Journal of Materials Research and Technology-JMR and T,
Vol. 18,
pp.2363-2367,
2022
-
"Improvement of ?' coarsening model in high ?' volume fraction Ni-base superalloys containing different Ta/W ratio"
M. Mostafaei,
S.M. Abbasi,
Mohammad Ali Mostafaei
JOURNAL OF ALLOYS AND COMPOUNDS,
Vol. 885,
2021
-
"Serrated yielding behavior after cold and hot rolling of a high Mg content Al-Mg alloy"
Mohammad Ali Mostafaei
JOURNAL OF ALLOYS AND COMPOUNDS,
Vol. 811,
2019
-
"Grain-refining ability of ultra-rapid annealing for low-carbon steel severe plastic deformation"
Mohammad Ali Mostafaei,
Mohsen Kazeminezhad
Materiali in Tehnologije,
Vol. 51,
pp.173-177,
2017
-
"Microstructural evolution during ultra-rapid annealing of severely deformed low-carbon steel strain temperature and heating rate effects"
Mohammad Ali Mostafaei,
mohsen kazeminezhad
International Journal of Minerals Metallurgy and Materials,
Vol. 23,
pp.779-792,
2016
-
"Effect of Starting Microstructure through Severe Plastic Deformation and Ultra-Rapid Annealing of Low-Carbon Steel"
Mohammad Ali Mostafaei,
Mohsen Kazeminezhad
STEEL RESEARCH INTERNATIONAL,
Vol. 87,
pp.1527-1533,
2016
-
"Microstructure and mechanical properties improvement by ultra-rapid annealing of severely deformed low-carbon steel"
Mohammad Ali Mostafaei,
mohsen khazeminezhad
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 655,
pp.229-236,
2016
-
"Study on microstructure and mechanical characteristics of low-carbon steel and ferritic stainless steel joints"
Mahmoud Sarkari Khorrami,
Mohammad Ali Mostafaei,
hesam pouraliakbar,
Amir Hossein Kokabi
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 608,
pp.35-45,
2014
-
"Analyses on the Flow Stress of an Al-Mg Alloy During Dynamic Recovery"
Mohammad Ali Mostafaei,
M. Kazeminezhad
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,
Vol. 22,
pp.700-705,
2013
-
"A novel approach to find the kinetics of dynamic recovery based on hot flow curves"
Mohammad Ali Mostafaei,
M. Kazeminezhad
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 544,
pp.88-91,
2012
-
"Hot deformation behavior of hot extruded Al6Mg alloy"
Mohammad Ali Mostafaei,
M. Kazeminezhad
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 535,
pp.216-221,
2012
-
"تاثیر دمای آنیل فوق سریع بر ریزساختار فولاد کم کربن به شدت تغییر شکل یافته"
محمدعلی مصطفائی،
محسن کاظمی نژاد
مواد نوین،
نسخه 10،
صفحات:1-12،
1399
